Number of Articles: 11
Properties of Welded Copper Tubes Fabricated Via Friction crush Welding
Volume 40, Issue 6 , June 2022, Page 840-847
Abstract
The welding process is one of the fabrication processes in which tubes can be performed for structural purposes and transport liquids or gases. This study is focused on the manufacturing, ... Read More ...Structural Characterization of (Mg(1-x)pbxO)-NPs by Modified Pechini Method
Volume 40, Issue 6 , June 2022, Page 11-20
Abstract
The structural characterization was discussed in the present paper of the pure MgO nanoparticles and the doped (Mg(1-x)pbxO) nanoparticles specimens, where (0 ≤ x ≤ 0.03). The ... Read More ...Effect of Voltage on Electrode Wear Rate (EWR) in the Electrical Discharge Machining (EDM) for Stainless Steel AISI 444
Volume 40, Issue 6 , June 2022, Page 21-30
Abstract
Electrical Discharge Machining process (EDM) is a nontraditional metal removal technique that uses thermal energy to erode the workpiece without generating any physical forces of cutting ... Read More ...Preparation of CuO/ZnO Nano-Particles Using Sol-Gel Technique and Studying the Characterization
Volume 40, Issue 6 , June 2022, Page 862-868
Abstract
Copper oxide (CuO) and zinc oxide (ZnO) are two of the most promising oxides under development right now. The sol-gel technique was used to make Nano composite particles NCPs of ZnO-CuO. ... Read More ...Improvement of Metal Forging Processes by Stresses and Temperatures Analysis
Volume 40, Issue 6 , June 2022, Page 869-878
Abstract
The mechanical components are produced by various fabrication methods, although forged products have excellent mechanical characteristics at a minimal cost. The stress and temperature ... Read More ...Influence of Machining Parameters on Surface Roughness in Chemical Machining of Silicon Carbide (SiC)
Volume 40, Issue 6 , June 2022, Page 879-884
Abstract
This study discussed the influence of chemical machining parameters such as (machining time, type of etchant, etching temperature, and concentration of the solution) on the surface ... Read More ...Effect of Abrasive Water Jet (AWJ) Parameters on Materials Removal Rate for Low Carbon Steel
Volume 40, Issue 6 , June 2022, Page 885-891
Abstract
Abrasive water jet (AWJ) is one of the most advanced and valuable non-traditional machining processes because of its massive advantages of removing metal from hard and soft metals. ... Read More ...Study the Growth of Apatite Layer on Biodegradable Glass as Bioactive Scaffolds
Volume 40, Issue 6 , June 2022, Page 892-900
Abstract
Bioglass offers a variety of uses for tissue engineering due to its good biocompatibility and chemical composition, similar to a mineral portion of the body. The synthesis of bioglass ... Read More ...Synthesis ZnO heterostructured nanophotocatalyst simulated solar light irradiation for removal contaminate Carbamazepine in aqueous solution
Volume 40, Issue 6 , June 2022, Page 901-910
Abstract
In this study, zinc oxide nanoparticles (ZnO) were produced in aqueous media to photodegrade harmful carbamazepine compounds (CBZ) in aqueous solution under simulated solar-light using ... Read More ...Studying the Effect of un Coated and Multilayer Coated Tools on Cutting Temperature in Turning Operation
Volume 40, Issue 6 , June 2022, Page 911-917
Abstract
The present work studies three variables (cutting velocity, feed rate, and cut depth) on hard turning cutting temperature of uncoated and multilayer-coated carbide (TiN, TiN/TiCN, TiN ... Read More ...Electrostatic Deposition of Poly(Methyl Methacrylate)/Titanium Carbide Coatings on Austenitic 316L Stainless Steel Implant
Volume 40, Issue 6 , June 2022, Page 918-925