Print ISSN: 1681-6900

Online ISSN: 2412-0758

Volume 40, Issue 12 (Production and Metallurgy Engineering

Volume 40, Issue 12 (Production and Metallurgy Engineering, Material Engineerin,19 Articles), December 2022

Research Paper

Investigation Nano-coating for the Corrosion Protection of Petroleum storage tanks Steel

Zainab Z. Ali; Baha S. Mahdi; Ameen D. Thamer

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1605-1613
DOI: 10.30684/etj.2022.131942.1074

This work studies the protection from corrosion in the inner surface of petroleum storage tanks by applying nano-coating on the AISI1018 steel type used in these tanks. BNi-2 alloy, used as coating layer, was deposited using the DC sputtering technique to obtain protection layers of nano-coating. The cyclic potential dynamic polarization technique is used to study and evaluate the resistant metal to localize corrosion, for example, pitting and crevice corrosion. The samples were evaluated in a 3.5% NaCl aqueous solution using the polarization method to determine the corrosion rate. The input parameters of deposition included ion current 16 mA, vacuum 10-1 mbar, time of deposition was 60 minutes, and the distance between target and substrate was 2.5 cm. The surface roughness of the uncoated specimens was (0.1466 µm), and after coating, it decreased to (0.0933µm). The most important factor that affects the corrosion of the coated steel surface is the surface topography of steel before coating, as it is known that the spattering process coats the facing surface to target better than the inclined surface topography. Therefore, some micro scratches non-coated well worked as nucleation for corrosion as detected in stereo microscope images for coated and uncoated surfaces. By calculating the corrosion rate from cyclic potential dynamic polarization for coated and uncoated workpieces, pitting and crevice corrosion improved approximately ten times compared to the uncoated AISI1018 steel surface.

Microstructure and Mechanical Properties of ZK60 Mg Alloy Processed by Cyclic Expansion-Extrusion (CEE) at Different Temperatures

Ahmed M. Marheb; Akeel D. Subhi

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1614-1620
DOI: 10.30684/etj.2022.133572.1194

In this work, the cyclic expansion extrusion (CEE) process was applied to ZK60 Mg alloy. The correlation between the evolved microstructure and mechanical properties was investigated. The CEE process was performed at a constant ram speed (15 mm/min) and at different processing temperatures (190, 270, and 350 °C). Optical and scanning electron microscopes, X-ray diffraction instruments, Vickers hardness tester, and tensile testing machine were utilized to examine the influence of CEE processing temperature on the characteristics of ZK60 Mg alloy. The XRD analysis showed that two phases were presented in the matrix of ZK60 Mg alloy, namely α-Mg and MgZn2, in small amounts. The CEE process reduced the size of α-Mg grains due to dynamic recrystallization, especially at the processing temperature of 190 °C. A slight coarsening of the α-Mg grains was observed with increasing processing temperature to 270 and 350 °C. The hardness value ​​of ZK60 Mg alloy was enhanced by about 11 to 19% using the CEE process compared to the as-extruded sample. The processing temperature greatly affected the mechanical properties, where a significant improvement of about 24% yield strength, 9% ultimate tensile strength, and 38% elongation was observed using a processing temperature of 190 °C. The characterization of the tensile fracture surface of the tested samples indicated that the ductile-brittle fracture mode was responsible for the failure.

Characterization of the Efficiency of Photo-Catalytic Ultrafiltation PES Membrane Modified with Tungsten Oxide in the Removal of Tinzaparin Sodium

Reham R. Abdullah; Kadhum M. Shabeeb; Aseel B. Alzubaydi; Alberto Figoli; Alessandra Criscuoli; Enrico Drioli; Qusay Alsalhy

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1621-1629
DOI: 10.30684/etj.2022.134070.1219

One of the polymeric membranes' main limitations is their susceptibility to fouling, lowering the membrane's performance with time. Therefore, incorporating nanomaterials in polymer matrices has attracted great attention in wastewater treatment applications. It's a promising approach for enhancing membrane hydrophilicity and performance.  Herein, ultrafiltration nanocomposite membranes were synthesized by applying the phase inversion method through immobilizing (0.1-0.4 wt.%) tungsten oxide (WO2.89) nanoparticles in a polyether sulfone (PES) matrix. Membrane's anti-fouling performance was evaluated against tinzaparin sodium. The data showed that the pure water flux improved with increasing nanoparticle loading, reaching its optimum value of 54.9 kg/m2 h at 0.4 wt.% WO2.89 nanoparticles compared to the neat membrane's 30.42 kg/m2 h. The results also demonstrated that the rejection efficiency and flux recovery ratio (FRR) against tinzaparin sodium was enhanced, by 44.89% and 12.69%, respectively, for the membranes modified with 0.4wt.% WO2.89 nanoparticles loading compared to the neat PES membrane. The data also showed that after exposing the nanocomposite membranes to UV light irradiation (λ=365 nm) and intensity (1200mW/cm2) for 1h, a further enhancement by 8.34% in FRR as compared to the membranes with the same percentage of nanoparticles loading without irradiation. It is concluded that the photocatalytic activity of WO2.89 nanoparticles in the decomposition of organic molecules on/close to the membrane surface was the impact that caused this improvement in membrane anti-fouling property

Parametric Optimization of Laser Conduction Welding between Stainless Steel 316 and Polyethylene Terephthalate Using Taguchi Method

Maraw A. Khioon; Kadhim A. Hubeatir; Mohanned M. AL-Khafaji

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1630-1637
DOI: 10.30684/etj.2022.132560.1131

A pulsed Nd:YAG laser with a fiber optic delivery system was used to accomplish a dissimilar joining of 316 stainless steel (SUS316) to polyethylene terephthalate (PET). Laser Conduction Welding (LCW) was applied as a welding technique to achieve a lap metal/polymer joint by applying the laser from the metal side. The heat was transferred from the metal layer to the polymer layer, which caused the melting and then solidifying of the polymer at the interface. The effect of three welding parameters, laser energy density, pulse duration, and welding speed, on joint force, was studied and discussed. To measure the joint force tensile shear test was conducted. Furthermore, the Taguchi method was used as a design experiment method to optimize the welding parameters by designing an orthogonal L9 matrix. The signal-to-noise ratio of each trial was calculated and plotted. The best welding parameters that gave the highest joint force were achieved. The maximum tensile force obtained was 525 N at 250 J/cm2 energy density, 15 ms pulse duration, and 20 mm/min welding speed. Finally, the comparison between the weakest and the strongest joints was carried out to show the difference between welding with the optimal parameters and any other set of parameters.

The Impacts of Calcium Ions Substitution in Hydroxyapatite with Neodymium and Zinc on Biological Properties and Osteosarcoma Cells

Suha Q. AL-Shahrabalee; Hussein A. Jaber

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1638-1646
DOI: 10.30684/etj.2022.133915.1217

Hydroxyapatite (HA) is one of the important biomaterials in the medical field, especially in bone treatment, because of its biological properties close to human bone. A simple co-precipitation technique was used to integrate neodymium and zinc into HA by adding neodymium nitrate and zinc nitrate as a source of substituted elements during synthesis through the wet precipitation method with controlled temperature and pH. Finally, substituted HA was sintered at 800°C after completing the biomaterial preparation. The resulting Nd-Zn/HA was globe-like with nanoparticle size. The Ca+Nd+Zn/P ratio was equal to 1.63, which is relatively close to the molar ratio of bone. Also, the ability of Nd-Zn/HA to cause apoptosis in osteosarcoma cells was discovered. The anti-tumor actions are amplified when increasing the concentration of substituted HA. Therefore, Nd-Zn/HA is a potentially effective biomaterial in osteosarcoma treatment. Meanwhile, it has antibacterial and fungicidal properties against Staphylococcus aureus, Staphylococcus epidermidis, Streptococcus mutans, Escherichia coli, and Candida albicans—one of the important properties required in biomaterials to protect the part that is being treated after the biomaterial is implanted inside the body. The inhibition zone of Nd-Zn/HA ranged between (20-31)mm, much higher than gentamicin and nystatin.

Obstacle Avoidance and Path Planning of a Wheeled Mobile Robot Using Hybrid Algorithm

Tahseen F. Abaas; Alaa H. Shabeeb

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1647-1658
DOI: 10.30684/etj.2022.132929.1154

In the mobile robot workplace, the path planning problem is crucial. Robotic systems employ intelligence algorithms to plan the robot's path from one point to another. This paper proposes the fastest and optimal path planning of the wheeled mobile robot with collision avoidance to find the optimal route during wheeled mobile robot navigation from the start point to the target point. It is done using a modern meta-heuristic hybrid algorithm called IPSOGWO by combining Improved Particle Swarm Optimization (IPSO) with Grey Wolf Optimizer (GWO). The principal idea is based on boosting the ability to exploit in PSO with the exploration ability in GWO to the better-automated alignment between local and global search capabilities towards a targeted, optimized solution. The proposed hybrid algorithm tackles two objectives: the protection of the path and the length of the path. During, Simulation tests of the route planning by the hybrid algorithm are compared with individual results PSO, IPSO, and GWO concepts about the minimum length of the path, execution time, and the minimum number of iterations required to achieve the best route. This work's effective proposed navigation algorithm was evaluated in a MATLAB environment. The simulation results indicated that the developed algorithm reduced the average path length and the average computation time, less than PSO by (1%, 1.7%), less than GWO by (1%, 1.9%), and less than IPSO by (0.05%, 0.4%), respectively. Furthermore, the superiority of the proposed algorithm was proved through comparisons with other famous path planning algorithms with different static environments.

Evaluation of PCL Electrospun Scaffolds Concentration on Metformin Hydrochloride Release Ratio

Saja A. Moosa; Akram R. Jabur; Emad S. Al-Hassani; Ahmed M. Al-Shammari

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1659-1670
DOI: 10.30684/etj.2021.131990.1079

The study investigates the effect of polycaprolactone (PCL) concentration on the metformin hydrochloride (MH) release ratio of electrospun nanofiber scaffolds. Blend and emulsion electrospinning are used to produce the scaffolds. The performance of nanofibrous scaffolds was evaluated by morphology (Field Emission Scanning Electron Microscopy, FESEM), chemical (Fourier Transform Infrared Spectroscopy, FTIR), thermal (Differential Scanning Calorimetry, DSC), wettability, porosity, mechanical tests, and in vitro drug release. The average fiber diameter ranged from (189.29-2893.93 nm) according to the FESEM results, and it increased with PCL concentration. The average fiber diameter of the electrospun scaffold, prepared by the blend method (259.64±6.1 nm), is lower than that of the electrospun scaffold produced by the emulsion method (487.45±22.53 nm). Melting points of all drug-loaded scaffolds were identical to those of pure PCL polymer. Compared with blend electrospun nanofibers, emulsion electrospun nanofibers showed a marked increase in hydrophilicity. The tensile strength indicated an improvement in the mechanical properties with a decrease in the average fiber diameter. Moreover, the results show that the release of Metformin hydrochloride decreases with the concentration of polycaprolactone. Total MH release from (5% w/v) PCL-MH fibrous scaffolds for three-week was 71.11 % and 93.91 % from the emulsion and blend methods, respectively. The drug release ratio is lower in emulsion electrospinning than in blend because the drug is encapsulated by polymer and surfactant, which improves control and long-term drug delivery system DDS.

A Numerical Study of Friction Stir Welding for AA5754 Sheets to Evaluate Temperature Profile and Plastic Strain

Mustafa M. Hadi; Mohanned M.H. AL-Khafaji; Akeel D. Subhi

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1671-1682
DOI: 10.30684/etj.2022.134304.1237

A full-dimensions 3-D numerical model based on the Lagrangian approach has been employed to predict the peak temperature and the plastic strain distribution in the FSW of (AA5754) joints using ABAQUS software. The material’s model utilizes the classical plasticity model in addition to defining the thermophysical properties of the alloy using JMatPro software to increase the accuracy of the numerical results. The basic variables of FSW were three rotational speeds (930, 1460, and 1860 rpm) and three traverse speeds (35, 65, and 95 mm/min).  The influence of the rotational and traverse speed on temperature profile and plastic strain has been studied. The simulation results showed that increasing the rotational speed led to increasing the peak temperature, which concentrated under the tool’s bottom surface while increasing the traverse speed decreased the peak temperature recorded. The highest peak temperature was (497 oC) at a rotational speed of (1860 rpm) and a traverse speed of (35 mm/min). It was also found that the rotational speed increased the plastic strain starting from the tool’s neck and continuing along the pins’ position and gradually decreasing towards the bottom. In addition, a V-shape pattern has appeared in the temperature distribution across the workpiece’s cross-section, representing the heat loss during the FSW by the backplate due to heat conductance.

Improvement of Erosion Resistance of Aluminum- Copper Alloy Type 2024 by Plasma Nitriding

Mohammed H. Maseekh; Ali H. Ataiwi; Jamal J. Dawood

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1683-1689
DOI: 10.30684/etj.2021.131414.1034

To increase the erosion resistance of 2024 Al alloys, plasma nitriding surface treatment was used. Nitrogen and argon gases are injected into an evacuated chamber until the pressure reaches 15 Pa. The process requirements for normal plasma nitriding were heating at 440˚C for 8 hours, low voltage of 650 V, current of 25 mA, low gas consumption, and no air pollution. A continuous nitriding layer of AlN was formed. The microhardness reached a maximum value of 170 HV, about 3 times higher than that Al melts at, is transported upward through voids and capillaries in the AlN structures, and reacted with N plasma in the melt surface. The growth of the AlN structures promotes this transport of un-nitride alloy subjected to the same heat treatments. As a result, the erosion rate of the nitrided samples decreased by 10% when compared to the ones that are not nitrided.

Investigating the Effect of Different Parameters on Physical Properties of Metakaolin-Based Geopolymers

Ahmed J. Abed AL-Jabar; Hanna A. Al-Kaisy; Sarmad I. Ibrahim

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1690-1699
DOI: 10.30684/etj.2022.132691.1138

Recently, geopolymers have received widespread attention due to their ability to completely replace ordinary cement with better efficiency, lower cost, and less damage to the climatic environment. This paper aimed to prepare MK-based geopolymer cement at ambient temperature with different alkaline activators and processing parameters. XRD, PSA, DTA-TGA, SEM, and other techniques have characterized the prepared samples. ANOVA test was employed to identify the main effect of the processing parameters. Results showed that the incorporation of potassium ions has a negative effect on the physical properties of GP, in which the presence of such ions tends to decrease the density of GP. Furthermore, the apparent porosity and water absorption were increased. For Na and K, Na-activated GP, it was also concluded that the density of GP increases by increasing Si/Al ratios. Despite the Na-based GP processes having a larger density in compared to the K, Na-based ones. The results also suggested a strong effect of the W\MK ratio on physical properties, in which decreasing this ratio is necessary to achieve GP with better properties. The findings also revealed that a one-minute mixing period was sufficient for producing a homogeneous and dense GP paste.

The Effect of Ceo2 Addition on Transformation Temperatures and Wear Resistance of Cu-Al-Ni Shape Memory Alloys

Dina F. Hammadi; Raad S. Ahmed Adnan; Mohammed A. Al-Sarraf

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1700-1710
DOI: 10.30684/etj.2022.132840.1144

SMAs can switch from one crystallographic structure to another in response to temperature or stress stimuli. When SMAs are exposed to mechanical cyclic stress, they can absorb and discharge mechanical energy by experiencing a reversible hysteretic shape change. SMAs are widely used for sensing, actuation, impact absorption, and vibration damping. This work studied the effect of  CeO2 addition on the transformation temperature and wear resistance of Cu-Al-Ni SMAs. WhereCeO2 was added at different percent’s 0.5, 1, and 3 wt% to the base alloy, followed by casting and homogenization at 900oC. Some tests were carried out: Differential scanning calorimeter, Optical Microscope, Scanning Electron microscopy, Energy dispersion spectrometer, X-Ray Diffraction, and Wear and Hardness tests. OM and SEM tests reveal that both phases of martensite β and γ are found. Also, the additions of CeO2 show a visible effect on phase formation and transformation temperatures. It was observed that increasing of CeO2 particles in Cu-based SMAs owing to improve interfacial bonding between matrix and reinforcement and also observed that the variants become thicker with increasing in percent. Additions of different percentages of cerium oxide increase the hardness of Cu-Al-Ni SMAs. Due to the addition of CeO2 particles, the sample's wear rate decreases compared to pure SMAs.

The Effect of Infill Pattern on Tensile Strength of PLA Material in Fused Deposition Modeling (FDM) Process

Maria F. Jasim; Tahseen F. Abbas; Abdullah F. Huayier

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1711-1718
DOI: 10.30684/etj.2021.131733.1054

Fused deposition modeling (FDM) is an additive manufacturing (AM) process often used to build geometrically complex prototypes and parts. It is becoming more popular since it improves products by eliminating the need for high-priced equipment. Materials, printing methods, and printing variables all impact the mechanical characteristics of printed items. The process parameters of FDM affect the parts' quality and functionality. This study examines the influence of different infill patterns on test specimens made of polylactic acid (PLA) tensile strength. Total of 10 different infill patterns (IPs): Grid, Lines, Triangles, Tri-Hexagon, Cubic, Gyroid, Zig-zag, Concentric, Octet, and Cubic subdivision were taken as process variables. Samples were printed using processing parameters (speed 60 mm/s, layer height 0.1 mm, infill density 80%, extruded at 200◦C). The ASTM D638 tensile test was used to determine the tensile strength based on this printing parameter. According to tensile test results, the infill pattern significantly affects the tensile strength. The results showed that the concentric infill pattern has a higher tensile strength of 32.174 MPa, whereas the triangles infill pattern has a lower tensile strength of 20.934 MPa.

Effect of Adding MgO on Microstructure of Zirconia Toughened Alumina (ZTA) Composite for Medical Applications

Alaa S. Taeh; Farhad M. Othman; Alla A. Abdul-Hameed

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1719-1731
DOI: 10.30684/etj.2022.134694.1245

Zirconia toughened alumina (Biolox delta) is a new-generation ceramic with four times the strength of alumina alone, used in artificial joints. The composite ZTA, consisting of 82 wt. %Al2O3, 17 wt. % ZrO2, 0.5 wt. % Cr2O3, and 0.5 wt. % SrO, was made using the sol-gel process, starting with salts. To investigate the effects of MgO on the ZTA microstructure, two concentrations (0.25 and 0.5 wt. %) of MgO were added to biolox during gelation to study the ZTA microstructure. Powders were sintered in the air for 2 hrs. at 1450 ºC. X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive x-ray analysis (EDX) were used to characterize sintering powders. ZTA + xMgO structural characteristics differ from pure ZTA's.  According to XRD calculations, grainsize decreased from 41.82 nm to 31.88 and 26.83 nm with increasing MgO concentration, but the specific surface area (SSA) increased from 40.63 to 54.79 m2/gm while crystallization improved. SEM examination shows the composite has a homogeneous dispersion of shaped particles. The EDX test shows the composite's homogeneous element distribution. ZTA+ xMgO powders were more antibacterial than ZTA powders. MgO inhibits bacterial activity and grain formation in ZTA composite during sintering, which makes it a good choice for medical applications, mainly artificial joints.

An Investigation on The Effect of Carbon Nanoparticles on The Properties of Carbon Brushes

Ahmed A. Alasady; M. I. Mohammad; Suleyman Basturk Basturk

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1732-1744
DOI: 10.30684/etj.2022.135387.1270

The demand for carbon brushes with specific properties and improvements in production economics in recent years has led to increased interest in metal-graphite composites. Metal matrix composites are considered excellent materials to obtain properties superior to those of the constituent phases and meet the specific requirements of material application. In the present study, we suggested a new composite material by utilizing nanomaterials to improve the properties of metal-graphite composite material usually used as carbon brushes. This has been achieved by adding different percentages of 0.1-0.5wt % of carbon nanotubes, carbon nanospheres, or both to the metal matrix composite. The samples were prepared by powder metallurgy technique. The XRD results gave a sharp line and indicated a high crystalline structure and little amorphous, which improved the conductivity performance of the composite produced within the structure of this work. The density measurement chart results showed an increase in the amounts of the carbon nano additives leading to a decrease in the density of the sample. The investigation of nano additives on hardness showed that increases in the additive led to reduced hardness. On the other hand, the resistivity values have reduced gradually when there is an increase in the amounts of the carbon nano additives, especially on the CNT, which gives better results than CNS, which we obtained the resistivity value =(0.32 Ωcm), Comparing with commercial-grade containing free of nano additives (1.3Ω cm).

Nanocatalyst for the Degradation of Plastic Waste to Produce Paints

Shams N. Almutalabi; Mohammed Alzuhairi; F. A. Hashim

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1745-1752
DOI: 10.30684/etj.2022.132459.1118

Recycling consumed commercial polymers is considered a highly important issue that chemists and engineers must take care of to develop the proper recycling techniques. The main objective of this study is to find a radical solution to the problems of plastic waste by recycling plastic waste (water bottles) and studying the effect of the produced Degraded Polyethylene Terephthalate (DPET) on the properties of paints. DEPT was added in six quantities to the paint mixture (1, 3, 4, 5, 7, and 14 grams). The paints were evaluated using various tests, including scanning electron microscopy (SEM), viscosity, adhesion, brightness, color, ultraviolet reflectance, and accelerated weathering. Testing the paint mixtures showed that the samples were not affected by weather conditions. This indicates the improvement of the paint mixtures by adding quantities of DPET. This study concludes that the catalyst ratios used succeeded in cracking DPET and avoided the need for large quantities of the catalyst. The use of  DPET in various material applications reduces the cost due to the low cost of DPET production. The use of PET in sustainable applications conferred a radical solution to plastic waste problems worldwide. In this work, mixing plastic waste products, after their treatment, in the preparation of paint mixtures successfully contributed to improving the required specifications.

Improving Fatigue Corrosion Resistance of Turbine Blades Using Laser Processing

Zaman A. Abdulwahab; Sami I. Jafar; Sami A. Ajeel

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1753-1762
DOI: 10.30684/etj.2022.134330.1235

The present paper investigates the nanomaterial coatings effect on turbine blades by laser processing. The present paper explores the impact of laser cladding parameters on the corrosion behavior of the resulting surface. Powders of Inconel 600 were deposited on the steel substrate. The surface can be thought of as the most important part of every engineering component. Unlike the rest of the component's volume, the surface is exposed to wear and becomes the place where most cracks form and corrosion initiates. Corrosion is one of the most harmful problems affecting turbine blades. In the current investigation, coating nanomaterials, namely Inconel 600, have been used to resist corrosion. The specimens of tests have been obtained from the part of the turbine blades in Al-Doura Station, located south of Baghdad. These specimens are separated into two groups: The 1st group is received specimens, and the 2nd group is with nanoparticle coating, including Inconel 600 coating applied by laser cladding. The procedure of cladding was implemented utilizing the following parameters :(11 j) pulse energy, (6 Ms.) pulse width, (12 Hz) pulse frequency, (132 W) laser average power, and (1.83 KW) laser peak power. The results show that the microstructure of steels after laser processing is greatly refined with equiaxed grains and highly homogeneous as compared with those of steels before laser treatment, resulting in a significant improvement in strength, toughness, and fatigue corrosion.

Supplier Ranking in Dental Sector Using Integrated Fuzzy (AHP-TOPSIS)

Asma A. Mohammed Ali; AllaEldin H. Kassam

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1763-1770
DOI: 10.30684/etj.2022.135731.1287

Choosing a suitable supplier of materials and equipment in the healthcare sector is essential because it directly affects the patient's health and the organization's effectiveness and quality of services. Moreover, studies on supplier ranking are few in the field of health, particularly in the dental sector. For this purpose, an integrated fuzzy (AHP-TOPSIS) model has been developed for supplier ranking in the dental sector. The F-AHP is used to evaluate the importance of criteria, and then the F-TOPSIS method is applied to the supplier ranking process. A real case study is conducted on dental composite filling suppliers. Six evaluation criteria are identified, and five potential suppliers are selected through a direct interview with a group of experts. Then a questionnaire is applied to 12 experts (dentists) to rate the importance of evaluation criteria and to evaluate suppliers based on evaluation criteria. Evaluating the importance of criteria using F-AHP indicated that quality is the most important criterion. It has a weight of 0.22, followed by esthetic and durability with a weight of 0.21 for both. Moreover, the result of ranking using F-TOPSIS indicated that supplier A5 is the top supplier with a value of  (0.532).

Investigation of Compression and Hardness for UHMWPE Bio-composites as Internal Bone Plate Fixation

Tamara R. Kadhim; Jawad K. Oleiwi; Qahtan A. Hamad

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1771-1782
DOI: 10.30684/etj.2022.135083.1258

Bone plates are essential for bone fracture healing because they modify the biomechanical microenvironment at the fracture site to provide the necessary mechanical fixation for fracture fragments. This paper addresses the use of composite bone plates in healing long-bone fractures such as transverse fractures of the femur. However, stress shielding in the bone due to metal plates can be reduced by designing implants with Bio-composites that involve Ultra high molecular polyethylene reinforced (UHMWPE) with Nano hydroxyapatite (n-HA) and Nano titanium dioxide (n-TiO2) particles at different weight fraction (0,1.5,2.5,3.5and 4. 5%) and 5% of carbon and Kevlar fibers. FRIT spectrum was used to identify the incorporation between the matrix and Nano particles, and the shifting in main peaks confirmed the good cross-linking within the composite structure. The specimens thus prepared were subjected to a compression test, hardness test, and density. The results indicated that UHMWPE+4.5%n-HA+CF hybrid biocomposite has the highest compressive strength and hardness properties. In contrast, UHMWPE+4.5%TiO2+CF has the highest density, which increased with increasing percentages of weight fraction of Nano-particles, where the compression strength 53 MPa, hardness property ranges 65.6 shore D, and density 1.09 (g/cm3). According to the current study's findings, it is possible to create bio-composites as internal fixation device with improved performance by placing different fiber reinforcements.

Epoxy-Nanoceramic Composites for 5G Antennas

Hasanain B. Altalebi; Alaa A. Atiyah; Saad B.H. Farid

Engineering and Technology Journal, 2022, Volume 40, Issue 12, Pages 1783-1790
DOI: 10.30684/etj.2022.134894.1254

Epoxy–nanoceramic composites of BiVO4 (BVO), LaNbO4 (LNO), and Li6Mg7Ti3O16 (LMT) were prepared using the solvent mixing method. The ceramic nano-fillers volume fractions were (5, 8, 10, and 12%). X-ray diffraction (XRD) and Atomic Force Microscopy (AFM) were used to investigate the crystal structure and size distribution of nanoceramics, respectively. The dielectric constant and loss tangent were measured in the frequency range of (4-8) GHz. The measurement technique was the waveguide approach via a Vector Network analyzer (VNA). The effect of the volume fraction of ceramic fillers on the dielectric constant and loss tangent of the composites at 5.28 GHz (5G) was investigated. This work aims to design composite materials for 5G antennas of lower cost while maintaining the properties of 5G antennas. The results show that an optimum volume fraction of the ceramic filler brings the dielectric properties to their best value. However, epoxy composite with a 5% volume fraction of LMT shows good microwave dielectric properties (dielectric constant = 2.17 and loss tangent = 0.011) at 5.28 GHz. In addition, epoxy- LMT composite with an exceptionally low volume fraction of 5% provides a low-cost material for a 5G antenna. Another aspect of the cost reduction is the elimination of the costly and troublesome compaction and high-temperature sintering process. Furthermore, the epoxy composite overcomes the disadvantages of the high brittleness of the sintered all-ceramic products. As a result, epoxy composite with the 5% volume fraction of LMT is a potential candidate for 5G antenna materials.