Number of Articles: 15
Experimental Investigation of Composite Steel-Concrete Arches
Volume 31, Issue 13 , August 2013, Page 2393-2414
Abstract
This research is concerned with behavior of composite steel-concrete arches under static load. For this purpose, eight models of composite steel-concrete arches are fabricated as test ... Read More ...Ordinary and Encased Stone Columns with Two Different Relative Densities
Volume 31, Issue 13 , August 2013, Page 2415-2432
Abstract
Stone columns technique is most commonly used in increasing bearing capacity, reduces and controls the compressibility and accelerates the rate of consolidation of soft saturated clay. ... Read More ...Study the Effect of Fibers Volume Fraction and their Orientations on the Properties of the Hybrid Composite Materials
Volume 31, Issue 13 , August 2013, Page 2433-2447
Abstract
This studying deals with the study of the effect of fiber volume fraction of the carbon, glass and Kevlar fibers and their orientation on the properties of Hybrid composite material. ... Read More ...Improvement of the Strength of Spot Welding Joint for Aluminum Plates Using Powders as Additive
Volume 31, Issue 13 , August 2013, Page 2448-2461
Abstract
This research is interest in increasing the strength of spot welding joint for thin commercial Aluminum by adding casting component to the welding zone in the form of powder. Those ... Read More ...Shear Strength of Reinforced Concrete Beams under Distributed Loading
Volume 31, Issue 13 , August 2013, Page 2462-2476
Abstract
This work confirms results indicated by previous research that uniformly distributed loading leads to higher reinforced concrete (RC) beam shear capacitycompared to 1 or 2 point loading. ... Read More ...High Performance of Silica Fume Mortars for Ferrocement Applications
Volume 31, Issue 13 , August 2013, Page 2477-2488
Abstract
The current study deals with obtaining the high performance mortars to use in the applications of ferrocement. The main problem that has greatly affected the performance of mortar is ... Read More ...Theoretical Evaluation of Required PlasticWork in Bulging of Statically loaded Plate
Volume 31, Issue 13 , August 2013, Page 2489-2503
Abstract
Finding the amount of plastic deformation into metallic plates,metallicstructures, ships frame, bodies of different types of cylinders and reservoirsbodies as a result of exposure tostaticor ... Read More ...Relevant Problem of a Hydraulic Jump at Diyala Weir and the Proposed Remedy
Volume 31, Issue 13 , August 2013, Page 2504-2512
Abstract
This study aims to analyze the Diyala weir problems and compares it with the safe limit and proposes the treatment for these problems. One of the most influencing problems in the site ... Read More ...Influence of Noisy Environment on the Speech Recognition Rate Based on the Altera FPGA
Volume 31, Issue 13 , August 2013, Page 2513-2530
Abstract
This paper introduce an approach to study the effects of different levels of environment noise on the recognition rate of speech recognition systems, which are not used any type of ... Read More ...Performance Analysis of Three Phase Cascaded Multilevel Inverter (CMLI) for Induction Motor Drives
Volume 31, Issue 13 , August 2013, Page 2531-2547
Abstract
Traditional high-frequency pulse width modulation (PWM) inverters for motor drives have several problems associated with their high switching frequency which produces high voltage change ... Read More ...Integration of Swarm Intelligence and Artificial Neural Network for Medical Image Recognition
Volume 31, Issue 13 , August 2013, Page 2548-2560
Abstract
Neural network technology plays an important role in the development of new medical diagnostic assistance or what is known as “computer aided” that based on image recognition.Thispaper ... Read More ...Preparation of Aluminum Matrix Composite Reinforced with Alumina Particles by In- Situe Method
Volume 31, Issue 13 , August 2013, Page 2561-2571
Abstract
In this work an Aluminum matrix composite reinforced with alumina prepared by insitu (liquid-gas) method were investigated. Gas was represented by an oxygen with flow rate 50, 100, ... Read More ...Experimental Investigations of Hole - EDM to Optimize Electrode Wear through Full Factorial of Design of Experiment
Volume 31, Issue 13 , August 2013, Page 2572-2579
Abstract
Electrical discharge machining (EDM) is a process where the material removal of the workpiece is achieved through high frequency sparks between the tool (electrode) and the workpiece ... Read More ...A Computer Program for Calculating the Circular Product Dimensions During Deep Drawing Operations Steps
Volume 31, Issue 13 , August 2013, Page 2580-2595
Abstract
Deep drawing process is an important industrial processes where it has been extensively used. It is a process for converting the blank metal to make cylindricalshape in most of the ... Read More ...Some properties of accelerated cured no fine Lightweight concrete
Volume 31, Issue 13 , August 2013, Page 213-224